Best recommendation for crashed GSO gear

[swoleassnigga]

I have never used oils using gso before and today I received my order from the mail and the oil is gelled. I left it at room temp all day and it is still gell.
I’m assuming I just heat a little? Any experience on this would be helpful.

 

[JohnnyCashew]

This thread has a few ideas mentioned https://www.steroidsourcetalk.org/m...-without-taking-flip-top-off?highlight=Candle

 

[Swole_Guacamole]

If it’s not tren I just put it on a warm stove burner for like 30 seconds to a minute and it uncrashes everytime. if it’s tren then I use a wax heater

 

[swoleassnigga]

Swole Guacamole" pid='37638' dateline='1547693090:

If it’s not tren I just put it on a warm stove burner for like 30 seconds to a minute and it uncrashes everytime. if it’s tren then I use a wax heater

I’ve been researching steroids and using SST for a few years. I have read how to recover crashed gear. This was the first time I had gear crash before. I think it was left in the mail box overnight and it was 25 degrees. Just looking for a little advice since I trust this site. After all this is the dumb questions’ forum.
Thank you for the response.

 

[system]

swoleassnigga" pid='37479' dateline='1547607413:

I have never used oils using gso before and today I received my order from the mail and the oil is gelled. I left it at room temp all day and it is still gell.
I’m assuming I just heat a little? Any experience on this would be helpful.

Still the best method that uses dry heat, works quickly and cools quickly so the hormone doesn’t degrade, can be repeated as many times a s necessary, doesnt require extra setup, equipment or hands on lab work time… MICROWAVE for 15 seconds then remove vial and shake vigorously. Repeat until crystals are gone.

Second best and completely hands free-
some kind of tray, garden flat, baking dish cake pan, whatever. Put am electric heating blanket under it, put all crashed vials in the pan, turn heat to med, pput another pan or lid of sorts on top and walk away. Check tmrw.

 

[espressofan]

+1 on the candle warmer. I suggest not leaving the vial on heat too long without venting with a pin. I’ve heard at one story of a vial breaking while someone was in the shower

 

[DNPstoney]

SouthernCompounding" pid='39403' dateline='1548852626:

swoleassnigga" pid='37479' dateline='1547607413:

I have never used oils using gso before and today I received my order from the mail and the oil is gelled. I left it at room temp all day and it is still gell.
I’m assuming I just heat a little? Any experience on this would be helpful.

Pick up a candle warmer and set the vials on. Shake them every 3-5 minutes until everything mixes back up.

Honestly, this. Candle warmers are pretty cheap (~$15 for a 2 pack on Amazon) and it is an easy fix for crashed gear. I originally bought it because I had some crashed gear, but now I just throw all the stuff I am pinning on one for ~5 mins before I pin. It makes pulling and pinning so much smoother; the only annoying thing is holding a hot vial.

 

[espressofan]

Anyone notice the oil get thin after its warm, and sometimes a small amount leaks from the vial when you are going to draw it?

 

[Masterofron]

espressofan" pid='39857' dateline='1549111903:

Anyone notice the oil get thin after its warm, and sometimes a small amount leaks from the vial when you are going to draw it?

Heat will obviously change the viscosity of the gear. From syrupy—> watery. I heat my gear up prior to every pin in a glass of hot water. This allows it to flow through insulin needles quickly. Also this will fix crashed gear.

 

[Bearslovecheese]

Received gear Thursday in the second of two days where our temps were -24 to -30 F overnight (consecutive record setting cold lows) and one vial was pretty crashed and one looked like it was thinking about it. Anyways, take wax tray off of wife’s candle warmer in bathroom and left them for about 30 minutes. Came back and perfect! I heat everything before drawing/pinning with 30g .5" needles anyways. SO. MUCH. NICER. Drawing, injecting, everything just seems smoother.

 

[swoleassnigga]

Thank you EVERY BODY! this is exactly what I was looking for. I researched the shit out of Steroids before I decided to start using them. Of course I have read about crashed gear and how to fix it. I was looking for the little tricks that only labs and guys that have been pinning for many years would know. Thanks again. LOVE YOU MAN! LOL